Object Search
43 results. Displaying results 1 - 43.
filters
- Department Industrial Remove filter Industrial
- Department Militarywear Remove filter Militarywear
- Subject War Remove filter War
- Subject Retail Remove filter Retail
- Department Archaeology Remove filter Archaeology
Name/Title
A decorated piece of brass from a concertina. The brass grille is lightly decorated with scrollwork.
Accession No
A98.366
Name/Title
A decorated cast brass handle which is thought to have been part of a small nutcracker.
Accession No
PA2010.083
Name/Title
An oval brass door handle escutcheon with four holes countersunk in it and a square central hole. The escutcheon is bent and one fragment of it has broken loose.
Accession No
PA2010.081
Name/Title
A circular brass seal for the South Taranaki Bacon Company. " THE / COMMON / SEAL / OF / THE SOUTH TARANAKI BACON COMPANY LIMITED " is marked in raised letters on the seal. There are two small threaded holes on the reverse of the seal where presumably a handle would have been attached.
Accession No
PA2009.091
Name/Title
A brass forage cap badge of the 70th Regiment. The badge is shaped as a " 70 " with eyelets and a pin on the reverse.
Accession No
PA2010.082
Name/Title
A wheel pricker with a rounded wooden handle attached to a metal shank which is bent near the end. The shank has a circular toothed wheel mounted in a forked carrier which can be adjusted by a wingnut which can allow the wheel to be removed. " J DIXON " is stamped on one side of the shank.
Accession No
TM2003.023
Name/Title
A single crease with a rounded wooden handle attached to a gently curved shank which ends in a shield shaped head with a blunt edge. " 2 " is stamped on the head and some illegible writing is stamped in the shank.
Accession No
TM2003.024
Name/Title
A screw crease with a rounded wooden handle attached to a shank which ends in a shield shaped head which is split in two. A thumbscrew is threaded through the shank. There is a small leather strap at the end of the handle. " J E BUTLER LD. " is stamped into the top of the shank.
Accession No
TM2003.026
Name/Title
A double crease with a rounded wooden handle attached to a slightly curved shank which ends in an axe shaped head with two blunt edges. " 2 " is stamped into the head. " J.E BUTLER Ltd " is stamped into the shank.
Accession No
TM2003.027
Name/Title
A blunt edged knife with an upturned point on the blade and a rounded wooden handle. A brass band is around the handle where the shank meets the handle.
Accession No
TM2003.028
Name/Title
An edge shave with a rounded wooden handle attached to a slender shank which has a groove in the middle of the upper and lower side and a two pronged cutting edge. There is a brass band at the end of the handle where it is attached to the shank. " 1 " is stamped into the shank.
Accession No
TM2003.030
Name/Title
An edge shave with a rounded wooden handle attached to a slender shank which has a groove in the middle of the upper and lower side and a two pronged cutting edge. There is a brass band at the end of the handle where it is attached to the shank. " J DIXON " is stamped into the shank.
Accession No
TM2003.031
Name/Title
An edge shave with a rounded wooden handle attached to a slender shank which has a groove in the middle of the upper side and a two pronged cutting edge. There is a brass band at the end of the handle where it is attached to the shank. An indecipherable mark and " 4 " is stamped into the shank.
Accession No
TM2003.032
Name/Title
A leatherworking tool with a short blunt metal shank attached to a rounded handle. A brass band is wrapped around the portion of the handle where it joins the shank.
Accession No
TM2003.043
Name/Title
A shoe knife with a rounded wooden handle and a brass band where the handle joins the blade. There is an illegible manufacturer's mark on one side of the blade.
Accession No
TM2003.045
Name/Title
A fudge wheel which has a serrated wheel set to revolve on a steel shank that is attached to a rounded wooden handle.
Accession No
TM2003.050
Name/Title
A welt trimming knife with a circular cutting head mounted on a wooden handle. There is a brass band where the head is fixed to the handle. There are two illegible manufacturer's marks stamped on the blade. One of them may read " SNELL & ATHERTON " and there is a star design also stamped on the blade.
Accession No
TM2003.055
Name/Title
A purse crease with a rounded wooden handle attached to a shank which ends in a rounded head with two blunt edges." T DIXON & SON " is stamped into the shank.
Accession No
TM2003.056
Name/Title
A double crease with a rounded wooden handle attached to a slightly curved shank which ends in an axe shaped head with two blunt edges. " 3 " is stamped into the head. " J E BUTLER LD. " is stamped into the shank.
Accession No
TM2003.061
Name/Title
A double crease with a rounded wooden handle attached to a slightly curved shank which ends in a shield shaped head with two blunt edges. " J E BUTLER LD." is stamped on the side of the shank.
Accession No
TM2003.063
Name/Title
A wheel pricker with a rounded wooden handle attached to a metal shank which is bent near the end. The shank has a circular toothed wheel mounted in a forked carrier. "G.S.C.S Borne & Co" is stamped into one side of the shank. "ESTD1826" is stamped on the other side in a rectangle. "6" is stamped on top of the shank.
Accession No
TM2003.064
Name/Title
An American racer with a slender shank that has a narrow groove running down the centre. The shank is attached to a rounded wooden handle and there is a brass band around handle where it joins the shank. " 2 " is stamped on the top of the shank along with some other illegible manufacturers marks.
Accession No
TM2003.065
Name/Title
A single crease with a rounded wooden handle attached to a gently curved shank which ends in a shield shaped head with a blunt edge. A series of dents are stamped into the brass band where the shank joins the handle.
Accession No
TM2003.066
Name/Title
A fudge wheel which is made up of a serrated wheel set to revolve on a steel shank attached to a rounded wooden handle. An illegible maker's mark is stamped on a side of the shank.
Accession No
TM2003.067
Name/Title
A fiddler which has a smooth metal blade mounted in a rounded wooden handle. The blade is a flat half round which tapers slightly towards a rounded tip. A brass brand is fitted around the handle where the blade joins it. "GRA" is stamped very faintly on the wooden handle.
Accession No
TM2003.071